Bosch Boren en bits - pagina 34

Boorstift, voor beton, versterkt beton, solid brick, concrete building block, sand brick, lime brick, 18 mm, SDS-max, lengte: 340 mm

25 mm schroevendraaierbit, 2xPZ2

The impact control screwdriver bit is very robust and can withstand even the high power of impact screwdrivers

Bosch 2 608 522 470 schroevendraaierbit 3 stuk(s)

3 x Bosch professional screwdriver bit PZ insert bit – PZ1, PZ2, PZ3, length 25 mm, hex shank

Bosch Bit extra-hard

Boor, voor metaal, spiraalboor, 5 stuks, 8 mm, zeskantig, lengte: 117 mm

Router bit set, for wood, plastic, fibreboard, abrasive materials, plasterboard, soft wall tile, 5 pieces, 3.17 mm, length: 70 mm

Bosch HSS Twist Drill Bits PointTeQ

The long ground HSS spiral drill bit for drilling deep holes through metal with maximum precision. Its length allows for deep drilling with this long drill head. The exposed 135-degree two-part self-centering tip of the drill head combines active cutting with perfect centering without displacement for maximum precision. With the two-part tip, it is also unnecessary to mark pilot holes in advance or pilot bore up to 10 mm. This precision-ground drill head, made of HSS (high-speed steel), provides up to 40% faster drilling and up to 50% lower clamping pressure than standard ground HSS cutting edge drill heads. The long ground HSS spiral drill bit is manufactured according to DIN 340. The drill head is of type N (not angle) with a 135-degree tip and a diameter tolerance of h8. This drill head is designed for drilling deep holes in alloyed and non-alloyed steel, cast steel, cast iron, sintered iron, reduced cast iron, non-ferrous metals and hard plastic. It has a cylindrical shaft system (the shaft has the same diameter as the drill head) and is intended for use in drilling stands and screwdrivers
Package contains one piece.

The long ground HSS spiral drill bit for drilling deep holes through metal with maximum precision. Its length allows for deep drilling with this long drill head. The drill head's exposed 135-degree two-part self-centering tip combines active cutting with perfect centering without displacement for maximum precision. With the two-part tip, it is also unnecessary to mark pilot holes in advance or pilot bore up to 10 mm. This precision-ground drill head, made of HSS (high-speed steel), provides up to 40% faster drilling and up to 50% lower clamping pressure than standard ground HSS cutting edge drill heads. The long ground HSS spiral drill bit is manufactured according to DIN 340. The drill head is of type N (not angle) with a 135-degree tip and a diameter tolerance of h8. This drill head is designed for drilling deep holes in alloyed and non-alloyed steel, cast steel, cast iron, sintered iron, reduced cast iron, non-ferrous metals and hard plastic. It has a cylindrical shaft system (the shaft has the same diameter as the drill head) and is intended for use in boring stands and screwdrivers
Package with one piece.

The SDS plus-5 drill bit ensures problem-free drilling. The grooved carbide tip with notches ensures smooth drilling and easily penetrates the material without getting stuck, even in concrete. The Activeteq centering tip guides the drill position from the start without shaking or displacement and ensures precise hole diameter. AWB soldering and hardening technology reduces vibration during drilling, so the user is not burdened. The drill bit is suitable for masonry and concrete. The visible wear indicator shows if the hole diameter is still within tolerance when inserting dowels. The drill head is PGM certified by the PGM Masonry Drill Bit Association Board, guaranteeing tight tolerances, accurate drilling, and efficient fastening. The drill head is made in Germany. Compatible with SDS plus holder rotary hammers.
Package of 1 piece.

The step drill bit is made of HSS (high-speed steel) and provides a long lifespan when used with coolant. Laser-marked numbers on both flutes provide highly visible and durable marking of the hole diameter. Additionally, the 3-flat shank prevents slipping in the drill chuck and provides efficient transmission with high torque. The HSS step drill head delivers smooth, burr-free drilling in multiple diameters with a single bit. It is ideal for deburring, drilling round holes, and enlarging existing ones. No center punch is needed because the split point allows for easy starting. Its CNC-ground flute enables optimized chip removal and less vibration for smooth drilling. The most optimal cutting edge and absolute smoothness are ensured thanks to axial and radial relief grinding. This step drill bit is suitable for use on thin materials such as non-ferrous metals, sheet plastic, sheet steel, plastic, and stainless steel.
9 steps Ø 4-5-6-7-8-9-10-11-12 mm

The CYL-5 drill bit head guarantees extra long lifespan when drilling in concrete and stone. The Bosch-developed carbide material combined with diamond-ground cutting edges provides an extremely durable drill bit head. The variable design with 2 flutes and short, variable pitch significantly reduces flute friction and ensures efficient dust removal and less wear. The Bosch Power Grip shank system enables 100% power transmission from the machine to the drill bit head, so that the power is optimally utilized directly for the drilling task, and reduced power loss means less wear. For drilling fixing holes in concrete, natural stone, and artificial stone material. The drill bit head is PGM-certified by the PGM Masonry Drill Bit Association Board and guarantees tight tolerances, accurate boreholes, and effective fastening. The drill bit head is compatible with the cylindrical shank system for all powered and battery-powered hammer drills.
Package of 1 piece.

The step drill bit head is made of HSS (high-speed steel) and coated with AlTiN (aluminum titanium nitride). This provides the longest possible lifespan and does not require the use of coolant. Laser-marked numbers in both spiral flutes provide highly visible and durable marking of the hole diameter. In addition, the 3-flat shank prevents slipping in the drill chuck and provides efficient transmission with high torque. The HSS step drill bit head delivers smooth, burr-free drilling in multiple diameters with a single drill bit. It is ideal for deburring, drilling round holes, and enlarging existing ones. It is not necessary to mark center points because the two-part tip provides easy starting. Its CNC-ground spiral flute allows for optimized chip removal and less vibration for smooth drilling. The most optimal cutting and absolute smoothness are ensured thanks to axial and radial clearance grinding. This step drill bit is suitable for use on thin materials such as non-ferrous metals, sheet plastic, sheet steel, plastic, and stainless steel.
9 steps Ø 4-5-6-7-8-9-10-11-12 mm

The HSS cobalt spiral drill provides long-lasting performance when drilling in stainless steel. The extended lifespan is due to a 5% cobalt alloy content and fully ground HSS (high-speed steel), which provides outstanding surface quality, wear resistance, and heat protection. Equipped with two cutting edges and two flutes, chips are removed quickly, so the hammer drill lasts even longer. This hammer drill can be used for alloyed and unalloyed steel, stainless steel, cast iron, cast steel, acid- and heat-resistant steel. The HSS spiral drill made of steel is manufactured according to DIN 338. The drilling head is of type N (notch angle) with a 135-degree point angle and a diameter tolerance of h8. Active cutting and perfect centering without displacement are achieved thanks to the two-part tip. This drilling head can be used for alloyed and unalloyed steel, stainless steel, cast iron, cast steel as well as acid- and heat-resistant steels. It has a cylindrical shaft system (the shaft has the same diameter as the drilling head) intended for use in boring stands or screwdrivers.
Package with one piece.

The SDS plus-5 drill bit ensures problem-free drilling. The grooved carbide tip with notches ensures smooth drilling and easily penetrates the material without getting stuck, even in concrete. The Activeteq centering tip guides the drill position from the start without shaking or displacement and ensures precise hole diameter. AWB soldering and hardening technology reduces vibration during drilling work, so the user is not burdened. The drill bit is suitable for masonry and concrete. The visible wear indicator shows if the hole diameter is still within tolerance when inserting dowels. The drill head is PGM certified by the PGM Masonry Drill Bit Association Board, guaranteeing tight tolerances, accurate drilling, and efficient fastening. The drill head is made in Germany. Compatible with SDS plus holder rotary hammers.
Package of 1 piece.

The flat drill is made of hardened steel with a centering point for precise drilling. The adjustable flat drill ensures high flexibility when drilling. The flat drill has a wedge-shaped blade with a screw for locking and feeding, which can be adjusted from 15-45 mm. The flat drill is ideally suited for general drilling tasks where larger holes of different diameters are required. The drill is suitable for medium-hard and soft wood as well as lighter building materials and wood panels.
Adjustable flat milling cutter, Ø 15 - 25 mm, Ø 25 - 45 mm

Boor, voor zachthout, hardhout, brad point boor, 14 mm, cilindrisch, lengte: 151 mm

The HSS spiral drill with PointTeQ allows for fast drilling in metal thanks to the design of the tip with PointTeQ. It is quick and easy to start drilling as the self-centering tip prevents wandering. Due to the increased drilling speed, less heat and wear are generated. The PointTeQ tip design ensures that it remains sharp and has a long lifespan. This drill is suitable for drilling in alloyed and non-alloyed steel, non-ferrous metals, cast steel, cast iron, and plastic. There is low risk of breakage, especially for drills with a diameter under 6 mm as they are made with an extremely flexible core. Its black oxide coating ensures quick chip removal. The HSS PointTeQ spiral drill is manufactured according to DIN 338 standards. The drill type is N (angle of flute) with a 135-degree point angle. It has a cylindrical shank system (the shank has the same diameter as hammer drills) and is intended for use in pillar drills or screwdrivers.
Package contains 2 pieces.

It has an external hexagonal shaft of 1/4 inch and is intended for universal mounting of screws with screwdrivers and power drills. This Extra Hard screwdriver bit is a good choice for versatile use. All tasks can be performed thanks to the bit's modified S2 steel and an optimized heat treatment process, which provides extra hard quality and enables sufficient performance in all tasks. The tapered torsion zone of the bit easily handles maximum circumferential speeds when absorbing force and vibrations during screw installation, making it suitable for all tasks. Drive unit ISO 1173 C6.3, 1/4" external hexagon