Bosch Boren en bits - pagina 33

The ground HSS spiral drill bit for drilling through metal with maximum precision. The exposed 135-degree split self-centering tip of the drill head combines active cutting with perfect centering without displacement for maximum precision. With the split tip, it is also unnecessary to mark center points in advance or pilot drill up to 10 mm. This precision-ground drill head, made of HSS (high-speed steel), provides up to 40% faster drilling and up to 50% lower clamping pressure than standard ground HSS cutting edge drill heads. This drill head is designed for drilling holes in alloyed and non-alloyed steel, cast steel, cast iron, sintered iron, reduced cast iron, non-ferrous metals and hard plastic. The ground HSS spiral bore head is manufactured according to DIN 338. The bore head is of type N (notch angle) with a 135-degree tip and a diameter tolerance of h8. It has a cylindrical shaft system (the shaft has the same diameter as the bore head) and is intended for use in drilling stands and screwdrivers.
Package with one piece.

The HSS spiral drill with PointTeQ allows for fast drilling in metal thanks to the design of the tip with PointTeQ. It is quick and easy to start drilling as the self-centering tip prevents wandering. Due to the increased drilling speed, less heat and wear are generated. The PointTeQ tip design ensures that it remains sharp and has a long lifespan. This drill is suitable for drilling in alloyed and non-alloyed steel, non-ferrous metals, cast steel, cast iron, and plastic. There is low risk of breakage, especially for drills with a diameter under 6 mm as they are made with an extremely flexible core. Its black oxide coating ensures fast chip removal. The HSS PointTeQ spiral drill is manufactured according to DIN 338 standards. The drill type is N (angle of flute) with a 135-degree point angle. It has a cylindrical shank system (the shank has the same diameter as hammer drills) and is intended for use in pillar drills or screwdrivers.
Package contains one piece.

Stalen borstelset met 4 stuks. Schijfborstel, verfborstel, cilinder stalen borstel, kopborstel.

The CYL-3 drill bit ensures long-lasting performance when drilling in concrete. The wear-resistant drill head is made of a special carbide material developed and produced by Bosch. The material is designed to withstand frequent use and provides extra durability for tasks in concrete. The drill head's efficient U-shape with 2 notches ensures effective dust removal, less friction, reduced heat generation and wear, extending the life of the bit. The drill bit provides long-lasting performance when drilling fastening holes in abrasive materials such as concrete and natural stone. The drill head is PGM certified by the PGM Masonry Drill Bit Association Board, guaranteeing tight tolerances, precise drilling and efficient fastening. The drill head is compatible with the cylindrical shank system for all powered and battery-powered hammer drills.
Package contains 1 piece.

The HSS cobalt spiral drill provides long-lasting performance when drilling in stainless steel. The extended lifespan is due to a 5% cobalt alloy content and fully ground HSS (high-speed steel), which provides outstanding surface quality, wear resistance, and heat protection. Equipped with two cutting edges and two flutes, chips are removed quickly, so the hammer drill lasts even longer. This hammer drill can be used for alloyed and unalloyed steel, stainless steel, cast iron, cast steel, acid- and heat-resistant steel. The HSS spiral drill made of steel is manufactured according to DIN 338. The drilling head is of type N (notch angle) with a 135-degree point angle and a diameter tolerance of h8. Active cutting and perfect centering without displacement are achieved thanks to the two-part tip. This drilling head can be used for alloyed and unalloyed steel, stainless steel, cast iron, cast steel as well as acid- and heat-resistant steels. It has a cylindrical shaft system (the shaft has the same diameter as the drilling head) intended for use in boring stands or screwdrivers.
Package with one piece.

The CYL-3 drill bit ensures long-lasting performance when drilling in concrete. The wear-resistant drill bit is made of a special carbide material developed and produced by Bosch. The material is designed to withstand frequent use and provides extra durability for tasks in concrete. The drill bit's efficient U-shape with 2 flutes ensures effective dust removal, less friction, reduced heat development and wear, and extends the life of the drill bit. The drill bit provides long-lasting performance when drilling fastening holes in abrasive materials such as concrete and natural stone. The drill bit is PGM-certified by the PGM Masonry Drill Bit Association Board, guaranteeing tight tolerances, precise drilling, and efficient fastening. The drill bit is compatible with the cylindrical shank system for all powered and battery-powered hammer drills.
Package with 1 piece.

Boor, spiraalboor, 6 mm, cilindrisch, lengte: 93 mm

Boor, voor beton, metselwerk, steen, 10 mm, cilindrisch, lengte: 120 mm

Boor, voor beton, metselwerk, 8 mm, SDS-plus, lengte: 165 mm

Boor, spiraalboor, 2 stuks, 3.5 mm, cilindrisch, lengte: 70 mm

Schroevendraaier bit, 3 stuks, torx, T30, hexagonaal, lengte: 25 m

The ground HSS spiral drill bit for drilling through metal with maximum precision. The exposed 135-degree split self-centering point of the drill head combines active cutting with perfect centering without displacement for maximum precision. With the split tip, it is also unnecessary to mark center points in advance or pilot drill up to 10 mm. This precision-ground drill head, made of HSS (high-speed steel), provides up to 40% faster drilling and up to 50% lower clamping pressure than standard ground HSS cutting edge drill heads. This drill head is designed for drilling holes in alloyed and non-alloyed steel, cast steel, cast iron, sintered iron, reduced cast iron, non-ferrous metals and hard plastic. The ground HSS spiral bore head is manufactured according to DIN 338. The bore head is of type N (not angle) with a 135-degree point and a diameter tolerance of h8. It has a cylindrical shaft system (the shaft has the same diameter as the bore head) and is intended for use in drilling stands and screwdrivers.
Package with one piece.

Bosch SDS-Quick multi-purpose drill bits

Boor, voor beton, metselwerk, 8 mm, SDS-plus, lengte: 215 mm

Boor, voor beton, metselwerk, 4 mm, SDS-plus, lengte: 115 mm

The HSS dowel drilling head ensures precise drilling in both soft and hard wood and can be used for both through holes and pocket holes. This extremely sharp drill with a centering point makes it possible to place the hole precisely. High-quality support cutters with precise edges produce splinter-free holes. The drill's two flutes prevent material from clogging the hole and ensure good material removal and a precise result. The drilling head is suitable for soft and hard wood as well as laminated boards and MDF. The dowel drilling head is made of HSS (high-speed steel) and ground from solid metal. The hexagonal shaft system ensures quick, tool-free drilling head changes. A hexagonal shaft system makes the drill bit suitable for portable screwdrivers and drill stands

Bosch 3-piece Concrete Drill Bit Set SDS-Quick

The ground HSS spiral drill bit for drilling through metal with maximum precision. The exposed 135-degree split self-centering point of the drill head combines active cutting with perfect centering without displacement for maximum precision. With the split tip, it is also unnecessary to mark center points in advance or pilot drill up to 10 mm. This precision-ground drill head, made of HSS (high-speed steel), provides up to 40% faster drilling and up to 50% lower clamping pressure than standard ground HSS cutting edge drill heads. This drill head is designed for drilling holes in alloyed and non-alloyed steel, cast steel, cast iron, sintered iron, reduced cast iron, non-ferrous metals and hard plastic. The ground HSS spiral drill bit is manufactured according to DIN 338. The type N (notch angle) of the borehead has a 135-degree point and a diameter tolerance of h8. It has a cylindrical shaft system (the shaft has the same diameter as the borehead) and is intended for use in drilling stands and screwdrivers.
Package with 10 pieces.

Boor, spiraalboor, 3.5 mm, cilindrisch, lengte: 70 mm (pak van 10)

Boor, voor beton, metselwerk, hamerboor, 8 mm, SDS-plus, lengte: 615 mm

Bosch Bit extra-hard

Bosch Bit extra-hard

Bosch 2 608 622 117 spaakwiel & wielborstel Komborstel 5 cm