Bosch Boren en bits - pagina 22

Details:
- Diameter mm: 121
- Diameter inches: 4 3/4
- Working length: 38mm

Gatenzaag, voor bakstenen, spaanplaat, zachthout, plastic verstevigd met glasvezel, soft tile, 51 mm

Boorstift, voor beton, versterkt beton, hamerboor, 28 mm, SDS-max, lengte: 520 mm

Boorstift, voor beton, metselwerk, versterkt beton, 16 mm, SDS-max, lengte: 540 mm

Bosch 2609255023

Bosch Bit extra-hard

Bosch Extra Hard-schroefbits

Schroefbit, voor roestvrij staal, zachthout, 1/4", phillips, PH2, zeskant, lengte: 152 mm

Boor, voor plastic, non-ferrometaal, gietijzer, gegoten staal, gelegeerd staal, ongelegeerd staal, spiraalboor van 14 mm diameter en cilindrische vorm met een lengte van 160 mm

Sanding plate, voor mortel, Starlock, korrel: 60, 70 mm x 87 mm

Boorstift, voor beton, metselwerk, versterkt beton, 24 mm, SDS-max, lengte: 520 mm

Boorset, voor beton, metselwerk, spiraalboor, 7 stuks, 5 mm, 6 mm, 8 mm, 10 mm, 4 mm en12mm. Lengte:75mm ,85mm ,100mm ,120mm en150mm

Boorstift, hamerboor, 12 mm, SDS-plus, lengte: 265 mm

Slijpschijf, voor roestvrij staal, staal, 5 stuks, 125 mm, korrel: 60, voor GWX Professional 750-125

Routerbit, voor laminaat, Flush Trim, 12.7 mm, lengte: 68 mm

Boorstift, voor beton, plastic, staal, zachthout, soft tile, 6 mm, lengte: 150 mm

Drill bit, for concrete, masonry, 14 mm, SDS-plus, length: 1005 mm

Boor, voor hout, slangenboor, 16 mm, zeskantig, lengte: 235 mm

The ground HSS spiral drill bit for drilling through metal with maximum precision. The exposed 135-degree split self-centering point of the drill head combines active cutting with perfect centering without displacement for maximum precision. With the split tip, it is also unnecessary to mark center points in advance or pilot drill up to 10 mm. This precision-ground drill head, made of HSS (high-speed steel), provides up to 40% faster drilling and up to 50% lower clamping pressure than standard ground HSS cutting edge drill heads. This drill head is designed for drilling holes in alloyed and non-alloyed steel, cast steel, cast iron, sintered iron, reduced cast iron, non-ferrous metals and hard plastic. The ground HSS spiral drill bit is manufactured according to DIN 338. The type N (notch angle) of the borehead has a 135-degree point and a diameter tolerance of h8. It has a cylindrical shaft system (the shaft has the same diameter as the borehead) and is intended for use in drilling stands and screwdrivers.
Package with two pieces.

The HSS spiral drill with PointTeQ allows for fast drilling in metal thanks to the design of the tip with PointTeQ. It is quick and easy to start drilling as the self-centering tip prevents wandering. Due to the increased drilling speed, less heat and wear are generated. The PointTeQ tip design ensures that it remains sharp and has a long lifespan. This drill is suitable for drilling in alloyed and non-alloyed steel, non-ferrous metals, cast steel, cast iron, and plastic. There is low risk of breakage, especially for drills with a diameter under 6 mm as they are made with an extremely flexible core. Its black oxide coating ensures quick chip removal. The HSS PointTeQ spiral drill is manufactured according to DIN 338 standards. The drill type is N (angle of flute) with a 135-degree point angle. It has a cylindrical shank system (the shank has the same diameter as hammer drills) and is intended for use in pillar drills or screwdrivers.
Pack of 10 pieces.

Doosboor, voor beton, 82 mm

Doosboor, voor beton, 122 mm

Doosboor, voor beton, 152 mm