Salus Vloerverwarming

230 wireless room thermostat for mounting in wall box, for Salus iT600 Heating System. Colour: White.

Quantum SQ610RF is a new smart room thermostat from SALUS. The appearance of the room thermostat is light and simple in a smart thin design. The room thermostat has a built-in rechargeable lithium battery and should not have any batteries changed. The SQ610RF is wireless and fits with a SALUS floor heating system or SALUS Smart Home system. When connected through SALUS Smart Home it is possible to monitor and change the thermostat settings from either PC, Smart Phone or tablet. SALUS Quantum SQ610RF offers the opportunity to increase comfort and reduce energy consumption.

Salus 24V NC actuator for underfloor heating with 30mm nut, can be used for all 24V underfloor heating systems.

Pre-paired set for 1 circuit underfloor heating incl. Quantum thermostat.

Quantum SQ610 is a new smart room thermostat from SALUS. The room thermostat look is light and simple in a smart thin design. The room thermostat must be connected to 230V. The SQ610 can be used freely for either wired systems or connected wirelessly to a SALUS floor heating system / SALUS Smart Home system. When connected through SALUS Smart Home it is possible to monitor and change the thermostat settings from either PC, Smart Phone or tablet. The SALUS Quantum SQ610 offers the opportunity to increase comfort and reduce energy consumption.

Thermische actuator voor vloerverwarming van Salus met een normaal gesloten (NC) functie en 24 V AC werking.

Deze Salus thermische telestat is gemaakt voor vloerverwarmingssystemen waarbij een gesloten NC-actuator vereist is.

• Producttype: thermische telestat
• Voor vloerverwarming
• Normaal gesloten (NC)
• 24 V AC

Een eenvoudige keuze voor vloerverwarmingsopstellingen die een Salus 24 V AC NC thermische actuator nodig hebben.

Amplifier for Salus iT600 heating system ZigBee signal.

230 wireless 8 zone control box for Salus iT600 underfloor heating system.

The THB23031 is an auto balancing actuator that is used to provide automatic balancing of your underfloor heating circuits. It has two temperature sensors that are connected to the UFH flow and return pipes (inlet and outlet of the UFH manifold). It will continuosly measure the temperatures and adjust the actuator position to maintain the correct temparatur differential between the manifold flow and return pipes (Delta T). This product has an IP54 rating means that the produkt will be protected against contamination from limited amounts of dust and other particles. Additionally, it will be protected from water sprays from all directions. ITG Dresden have confirmed that the Salus THB actuator is equivalent to the hydraulic balancing. In co-operation with ITG Dresden, The Salus THB actuator has been tested and improved. During independent testing it was confirmed that the installation of the Salus THB system in existing underfloor heating system will achieve the same results as a conventional balancing.

Wireless Thermostat with knob

Valve-insert for valve for Salus GVM manifold.

SALUS GVM-F underfloor heating manifold is a high flow manifold with manual balancing of each circuit.Each zone valve has on the flow pipe a flow meter that can be used for balancing. Alternatively, the built-in manual flow control integrated into the return valve on the return pipe can be used for balancing. Instructions on how to balance the circuit can be found in the distributor box.SALUS GVM-F underfloor heating distributor has a manual vent on each pipe and a drain valve with 1/2 ”thread for hose. Inlet and return pipe connection is 1 ”thread, and the actuator thread is 30 x 1.5 mmContains:Stainless steel manifold set with flow meterEuroconus set for 20 mm PEXVentilation valve on inlet and returnSwivel filling and drain valveMounting brackets for wall mountingWith individual room temperature control. SALUS GVM-F benefits are available with SALUS - wireless control.Properties:Available with SALUS insulation in form-stable EPPComplies with the installation requirements for insulation standard DS 452.Ready for wall mounting.Can be used with water / glycol mixtures with a mixing ratio of up to 30%.Euroconus are included for all inlets and outlets for 20 mm PEX / PE-RT pipe.• Can be integrated into the SALUS Smart Home solution.Can be operated directly from the room thermostat or from the mobile phone, tablet or computer.Benefits are made of stainless steel alloy AISI304 L Premium quality and extruded in dimension1 ”, for optimal distribution and minimum pressure drop.Maximum working pressure: 6 BarMaximum test pressure: 10 bar

Smart Home RE600 is a repeater that connects wirelessly to your Universal Gateway so it becomes an integral part of your Smart Home system. The RE600 can be used if you have an area in the house where there is a bad signal from your Universal Gateway, or if the range is insufficient.

Salus Quantum analog smart dial thermostat for UFH.Zigbee communication. Battery 2xAAAA.11 mm deep from wall. Can be paired with CO10RF (KL08RF) & UGE600 Gateway

Wireless actuator for radiator valve with 30mm nut and adapter for RA valve for Salus iT600 heating system

SALUS GVM-F underfloor heating manifold is a high flow manifold with manual balancing of each circuit.Each zone valve has on the flow pipe a flow meter that can be used for balancing. Alternatively, the built-in manual flow control integrated into the return valve on the return pipe can be used for balancing. Instructions on how to balance the circuit can be found in the distributor box.SALUS GVM-F underfloor heating distributor has a manual vent on each pipe and a drain valve with 1/2 ”thread for hose. Inlet and return pipe connection is 1 ”thread, and the actuator thread is 30 x 1.5 mmContains:Stainless steel manifold set with flow meterEuroconus set for 20 mm PEXVentilation valve on inlet and returnSwivel filling and drain valveMounting brackets for wall mountingWith individual room temperature control. SALUS GVM-F benefits are available with SALUS - wireless control.Properties:Available with SALUS insulation in form-stable EPPComplies with the installation requirements for insulation standard DS 452.Ready for wall mounting.Can be used with water / glycol mixtures with a mixing ratio of up to 30%.Euroconus are included for all inlets and outlets for 20 mm PEX / PE-RT pipe.• Can be integrated into the SALUS Smart Home solution.Can be operated directly from the room thermostat or from the mobile phone, tablet or computer.Benefits are made of stainless steel alloy AISI304 L Premium quality and extruded in dimension1 ”, for optimal distribution and minimum pressure drop.Maximum working pressure: 6 BarMaximum test pressure: 10 bar

SALUS GVM-F underfloor heating manifold is a high flow manifold with manual balancing of each circuit.Each zone valve has on the flow pipe a flow meter that can be used for balancing. Alternatively, the built-in manual flow control integrated into the return valve on the return pipe can be used for balancing. Instructions on how to balance the circuit can be found in the distributor box.SALUS GVM-F underfloor heating distributor has a manual vent on each pipe and a drain valve with 1/2 ”thread for hose. Inlet and return pipe connection is 1 ”thread, and the actuator thread is 30 x 1.5 mmContains:Stainless steel manifold set with flow meterEuroconus set for 20 mm PEXVentilation valve on inlet and returnSwivel filling and drain valveMounting brackets for wall mountingWith individual room temperature control. SALUS GVM-F benefits are available with SALUS - wireless control.Properties:Available with SALUS insulation in form-stable EPPComplies with the installation requirements for insulation standard DS 452.Ready for wall mounting.Can be used with water / glycol mixtures with a mixing ratio of up to 30%.Euroconus are included for all inlets and outlets for 20 mm PEX / PE-RT pipe.• Can be integrated into the SALUS Smart Home solution.Can be operated directly from the room thermostat or from the mobile phone, tablet or computer.Benefits are made of stainless steel alloy AISI304 L Premium quality and extruded in dimension1 ”, for optimal distribution and minimum pressure drop.Maximum working pressure: 6 BarMaximum test pressure: 10 bar

Salus Smart Home Button, 2- buttons in one.

SALUS GVM-F underfloor heating manifold is a high flow manifold with manual balancing of each circuit.Each zone valve has on the flow pipe a flow meter that can be used for balancing. Alternatively, the built-in manual flow control integrated into the return valve on the return pipe can be used for balancing. Instructions on how to balance the circuit can be found in the distributor box.SALUS GVM-F underfloor heating distributor has a manual vent on each pipe and a drain valve with 1/2 ”thread for hose. Inlet and return pipe connection is 1 ”thread, and the actuator thread is 30 x 1.5 mmContains:Stainless steel manifold set with flow meterEuroconus set for 20 mm PEXVentilation valve on inlet and returnSwivel filling and drain valveMounting brackets for wall mountingWith individual room temperature control. SALUS GVM-F benefits are available with SALUS - wireless control.Properties:Available with SALUS insulation in form-stable EPPComplies with the installation requirements for insulation standard DS 452.Ready for wall mounting.Can be used with water / glycol mixtures with a mixing ratio of up to 30%.Euroconus are included for all inlets and outlets for 20 mm PEX / PE-RT pipe.• Can be integrated into the SALUS Smart Home solution.Can be operated directly from the room thermostat or from the mobile phone, tablet or computer.Benefits are made of stainless steel alloy AISI304 L Premium quality and extruded in dimension1 ”, for optimal distribution and minimum pressure drop.Maximum working pressure: 6 BarMaximum test pressure: 10 bar

Insulated bace module with stainless floor heating manifold incl. Drain, air screw and 20mm connector. Rødgod distributors for domestic water incl. 15mm connector. The base modules have universal adaptation, so they fit the market's well-known brands with easy adjustment. Unique for SALUS base module. Connection at the top from right to left KV Cold water-VV Hot water-VF Heating forward-VR Heating return.Insulated distributors and pipes according to DS452The underfloor heating control is mounted directly on the bottom module DIN.

SALUS GVM underfloor heating manifold is a high flow distributor with manual balancing of each circuit.Each valve has a built-in manual flow control which is very easy to adjust. Instructions for balancing the circuit can be found in the distributor box.The SALUS GVM manifold has a manual vent on each pipe and a drain valve with 1/2 ”thread for hose. The inlet- and return- connection is 1 ”thread, and the thread for the actuators are 30 x 1.5 mmContains:Stainless steel distributor set with valveEurokonus for 20 mm PEXVentilation valve on inlet and returnSwivel filling and drain valveMounting bracket for wall mountingWith individual room temperature control.Salus GVM underfloor heating distributors can be supplied with SALUS wireless control.Properties of Salus Underfloor Heating Manifold:Available with Salus insulation in form-stable EPP.Meets the installation requirements for insulation standard DS 452.Can be used with water / glycol mixtures with a mixing ratio of up to 30%.Euroconus are included for all inlets and outlets for 20 mm PEX / PE-RT pipe.Ready for wall mounting.Can be integrated into the Salus Smart Home solution.Can be operated directly from the room thermostat and from the mobile phone, tablet or computer.The distribution pipes are made of stainless steel alloy AISI304 L Premium quality and extruded in dimension 1 ”for optimal distribution and minimum pressure drop.Maximum working pressure: 6 BarMaximum proofing pressure: 10 bar

Underfloor heating unit with shunt and manifold 1 sling. Incl. 20 mm nut connection for pex with Euroconus.

SALUS GVM underfloor heating manifold is a high flow distributor with manual balancing of each circuit.Each valve has a built-in manual flow control which is very easy to adjust. Instructions for balancing the circuit can be found in the distributor box.The SALUS GVM manifold has a manual vent on each pipe and a drain valve with 1/2 ”thread for hose. The inlet- and return- connection is 1 ”thread, and the thread for the actuators are 30 x 1.5 mmContains:Stainless steel distributor set with valveEurokonus for 20 mm PEXVentilation valve on inlet and returnSwivel filling and drain valveMounting bracket for wall mountingWith individual room temperature control.Salus GVM underfloor heating distributors can be supplied with SALUS wireless control.Properties of Salus Underfloor Heating Manifold:Available with Salus insulation in form-stable EPP.Meets the installation requirements for insulation standard DS 452.Can be used with water / glycol mixtures with a mixing ratio of up to 30%.Euroconus are included for all inlets and outlets for 20 mm PEX / PE-RT pipe.Ready for wall mounting.Can be integrated into the Salus Smart Home solution.Can be operated directly from the room thermostat and from the mobile phone, tablet or computer.The distribution pipes are made of stainless steel alloy AISI304 L Premium quality and extruded in dimension 1 ”for optimal distribution and minimum pressure drop.Maximum working pressure: 6 BarMaximum proofing pressure: 10 bar

SALUS GVM-F underfloor heating manifold is a high flow manifold with manual balancing of each circuit.Each zone valve has on the flow pipe a flow meter that can be used for balancing. Alternatively, the built-in manual flow control integrated into the return valve on the return pipe can be used for balancing. Instructions on how to balance the circuit can be found in the distributor box.SALUS GVM-F underfloor heating distributor has a manual vent on each pipe and a drain valve with 1/2 ”thread for hose. Inlet and return pipe connection is 1 ”thread, and the actuator thread is 30 x 1.5 mmContains:Stainless steel manifold set with flow meterEuroconus set for 20 mm PEXVentilation valve on inlet and returnSwivel filling and drain valveMounting brackets for wall mountingWith individual room temperature control. SALUS GVM-F benefits are available with SALUS - wireless control.Properties:Available with SALUS insulation in form-stable EPPComplies with the installation requirements for insulation standard DS 452.Ready for wall mounting.Can be used with water / glycol mixtures with a mixing ratio of up to 30%.Euroconus are included for all inlets and outlets for 20 mm PEX / PE-RT pipe.• Can be integrated into the SALUS Smart Home solution.Can be operated directly from the room thermostat or from the mobile phone, tablet or computer.Benefits are made of stainless steel alloy AISI304 L Premium quality and extruded in dimension1 ”, for optimal distribution and minimum pressure drop.Maximum working pressure: 6 BarMaximum test pressure: 10 bar

SALUS GVM underfloor heating manifold is a high flow distributor with manual balancing of each circuit.Each valve has a built-in manual flow control which is very easy to adjust. Instructions for balancing the circuit can be found in the distributor box.The SALUS GVM manifold has a manual vent on each pipe and a drain valve with 1/2 ”thread for hose. The inlet- and return- connection is 1 ”thread, and the thread for the actuators are 30 x 1.5 mmContains:Stainless steel distributor set with valveEurokonus for 20 mm PEXVentilation valve on inlet and returnSwivel filling and drain valveMounting bracket for wall mountingWith individual room temperature control.Salus GVM underfloor heating distributors can be supplied with SALUS wireless control.Properties of Salus Underfloor Heating Manifold:Available with Salus insulation in form-stable EPP.Meets the installation requirements for insulation standard DS 452.Can be used with water / glycol mixtures with a mixing ratio of up to 30%.Euroconus are included for all inlets and outlets for 20 mm PEX / PE-RT pipe.Ready for wall mounting.Can be integrated into the Salus Smart Home solution.Can be operated directly from the room thermostat and from the mobile phone, tablet or computer.The distribution pipes are made of stainless steel alloy AISI304 L Premium quality and extruded in dimension 1 ”for optimal distribution and minimum pressure drop.Maximum working pressure: 6 BarMaximum proofing pressure: 10 bar