Tech-Protect Mobiel - Beschermend glas - pagina 2

Tech-Protect Glass Flex+ is a revolutionary hybrid glass that provides maximum protection for the watch screen without compromise. The ultra-thin design of just 0.28 mm makes it virtually invisible yet extremely durable. The ceramic coating with a hardness of 7H effectively protects against scratches and pressure, while maintaining perfect clarity and full touch sensitivity of the screen.

The biggest advantage of Glass Flex+ hybrid glass is its resistance to cracking and shattering – unlike traditional tempered glass, it does not break into sharp shards in the event of an impact, which significantly increases the safety of use. The flexible design allows for a snug fit against the watch screen without creating air bubbles.

Tech-Protect Glass Flex+ is the ideal solution for active users who value reliable screen protection on a daily basis and during sports.

Tech-Protect Glass Flex+ is a revolutionary hybrid glass that provides maximum screen protection without compromise. The ultra-thin design with a thickness of only 0.28 mm makes it virtually invisible and at the same time extremely durable. With a ceramic coating with a hardness of 7H, it effectively protects against scratches and pressure, maintaining perfect clarity and full sensitivity to touch. The biggest advantage? It doesn't crack or crumble like traditional tempered glass!

Tech-Protect Glass Flex+ is the perfect solution for those who value complete safety without compromise.

INSTALLATION INSTRUCTION:
1. The installation of this glass model is different from traditional tempered glass glued to a thin adhesive layer. Due to the thicker layer of glue, the process is a bit more demanding and requires precision.
2. Clean the watch screen thoroughly. Use a damp cloth to remove any dirt and fingerprints. Then wipe the screen with a dry, soft cloth to completely remove moisture. Finally, use dust stickers to get rid of dust and dust particles.
3. Carefully remove the protective film from the adhesive layer. Precisely align the glass with the screen and gently place it.
4. If any of the edges do not adhere properly, it is likely that the glass has been glued unevenly. In this case, they should be peeled off and re-glued until the desired effect is achieved.
5. Remove air bubbles by gently pressing the glass from the center to the edges. Use your finger or a soft cloth to do this, pushing the air out.
6. Due to the specificity of glass production (polishing, milling), the fitting may require several minutes of work. After proper installation, the final result is aesthetic and durable.

Tech-Protect Glass Flex+ is a revolutionary hybrid glass that provides maximum screen protection without compromise. The ultra-thin design with a thickness of only 0.28 mm makes it virtually invisible and at the same time extremely durable. With a ceramic coating with a hardness of 7H, it effectively protects against scratches and pressure, maintaining perfect clarity and full sensitivity to touch. The biggest advantage? It doesn't crack or crumble like traditional tempered glass!

Tech-Protect Glass Flex+ is the perfect solution for those who value complete safety without compromise.

INSTALLATION INSTRUCTION:
1. The installation of this glass model is different from traditional tempered glass glued to a thin adhesive layer. Due to the thicker layer of glue, the process is a bit more demanding and requires precision.
2. Clean the watch screen thoroughly. Use a damp cloth to remove any dirt and fingerprints. Then wipe the screen with a dry, soft cloth to completely remove moisture. Finally, use dust stickers to get rid of dust and dust particles.
3. Carefully remove the protective film from the adhesive layer. Precisely align the glass with the screen and gently place it.
4. If any of the edges do not adhere properly, it is likely that the glass has been glued unevenly. In this case, they should be peeled off and re-glued until the desired effect is achieved.
5. Remove air bubbles by gently pressing the glass from the center to the edges. Use your finger or a soft cloth to do this, pushing the air out.
6. Due to the specificity of glass production (polishing, milling), the fitting may require several minutes of work. After proper installation, the final result is aesthetic and durable.

Tech-Protect Glass Flex+ is a revolutionary hybrid glass that provides maximum screen protection without compromise. The ultra-thin design with a thickness of only 0.28 mm makes it virtually invisible and at the same time extremely durable. With a ceramic coating with a hardness of 7H, it effectively protects against scratches and pressure, maintaining perfect clarity and full sensitivity to touch. The biggest advantage? It doesn't crack or crumble like traditional tempered glass!

Tech-Protect Glass Flex+ is the perfect solution for those who value complete safety without compromise.

INSTALLATION INSTRUCTION:
1. The installation of this glass model is different from traditional tempered glass glued to a thin adhesive layer. Due to the thicker layer of glue, the process is a bit more demanding and requires precision.
2. Clean the watch screen thoroughly. Use a damp cloth to remove any dirt and fingerprints. Then wipe the screen with a dry, soft cloth to completely remove moisture. Finally, use dust stickers to get rid of dust and dust particles.
3. Carefully remove the protective film from the adhesive layer. Precisely align the glass with the screen and gently place it.
4. If any of the edges do not adhere properly, it is likely that the glass has been glued unevenly. In this case, they should be peeled off and re-glued until the desired effect is achieved.
5. Remove air bubbles by gently pressing the glass from the center to the edges. Use your finger or a soft cloth to do this, pushing the air out.
6. Due to the specificity of glass production (polishing, milling), the fitting may require several minutes of work. After proper installation, the final result is aesthetic and durable.

Tech-Protect Glass Flex+ is a revolutionary hybrid glass that provides maximum screen protection without compromise. The ultra-thin design with a thickness of only 0.28 mm makes it virtually invisible and at the same time extremely durable. With a ceramic coating with a hardness of 7H, it effectively protects against scratches and pressure, maintaining perfect clarity and full sensitivity to touch. The biggest advantage? It doesn't crack or crumble like traditional tempered glass!

Tech-Protect Glass Flex+ is the perfect solution for those who value complete safety without compromise.

INSTALLATION INSTRUCTION:
1. The installation of this glass model is different from traditional tempered glass glued to a thin adhesive layer. Due to the thicker layer of glue, the process is a bit more demanding and requires precision.
2. Clean the watch screen thoroughly. Use a damp cloth to remove any dirt and fingerprints. Then wipe the screen with a dry, soft cloth to completely remove moisture. Finally, use dust stickers to get rid of dust and dust particles.
3. Carefully remove the protective film from the adhesive layer. Precisely align the glass with the screen and gently place it.
4. If any of the edges do not adhere properly, it is likely that the glass has been glued unevenly. In this case, they should be peeled off and re-glued until the desired effect is achieved.
5. Remove air bubbles by gently pressing the glass from the center to the edges. Use your finger or a soft cloth to do this, pushing the air out.
6. Due to the specificity of glass production (polishing, milling), the fitting may require several minutes of work. After proper installation, the final result is aesthetic and durable.

Tech-Protect Glass Fit+ tempered glass is a high-quality protective accessory made of lightweight and precisely milled glass with a thickness of only 0.3mm.

The perfectly matched design fully preserves the sensitivity of the touchscreen. The manufacturer rates its hardness level at 9H on a ten-point scale, which translates into exceptional scratch resistance during everyday use.

The glass is characterized by crystal clarity, thanks to which it retains the natural colors and sharpness of the display. An additional advantage is a special oleophobic coating, which effectively minimizes the accumulation of fingerprints and other impurities on the surface of the glass, thus making it easier to keep it clean.

* Due to the various milling of the edges of the displays, after installing the film/protective glass on the screen, a slight air halo may be created around the screen! This is a natural situation and depends on the milling of the screen in a given piece.

INSTALLATION INSTRUCTIONS:
1) Start installation in the bathroom right after bathing - the water vapor will absorb all the dust from the atmosphere and it will not interfere with your installation.
2) Clean and degrease the surface of the screen thoroughly, then use a dry cloth to polish it to a shine.
3) Install the coating as evenly as you can - you can position it with two sheets, gluing them to the side of the device.
4) Get rid of air bubbles by pressing the whole thing down in a circular motion for a few dozen seconds. Do this so that the adhesive layer bonds to the screen as tightly as possible.

Tech-Protect Bundle 10-Pack Tempered Glass is a comprehensive set of high-quality screen protectors, designed for users who want maximum protection and reliability on a daily basis. Each glass in the set is made of durable, tempered material with a hardness of 9H, thanks to which it effectively protects the screen of the device from scratches, bumps and damage resulting from intensive use.

The ultra-thin design provides full clarity and does not affect touch sensitivity, guaranteeing a smooth, natural smartphone experience. With a precise cutout and a perfect fit, the glass adheres perfectly to the screen, while the oleophobic coating minimizes fingerprints and smudges.

A set of 10 pieces is an economical and convenient solution for both people who have several devices and for those who want to have spare protection always at hand. It is also a great proposition for services and sellers of GSM accessories.

* Due to the various milling of the edges of the displays, after installing the film/protective glass on the screen, a slight air halo may form around the screen! This is a natural situation and depends on the milling of the screen in a given piece.

INSTALLATION INSTRUCTIONS:
1) Start installation in the bathroom right after bathing - the water vapor will absorb all the dust from the atmosphere and it will not interfere with your installation.
2) Clean and degrease the surface of the screen thoroughly, then use a dry cloth to polish it to a shine.
3) Install the coating as evenly as you can - you can position it with two sheets, gluing them to the side of the device.
4) Get rid of air bubbles by pressing the whole thing down in a circular motion for a few dozen seconds. Do this so that the adhesive layer bonds to the screen as tightly as possible.

Tech-Protect Easy Set+, i.e. the tempered coating for the display, is made of light and milled glass with a thickness of 0.3mm. The crystal clear glass ensures image clarity, perfect reproduction of color saturation and does not disturb the sensitivity of touch. In addition, it is covered with a high-quality oleophobic coating, which minimizes the amount of fingerprints or other impurities left.

Protective lens cap made of high-quality tempered glass with a hardness of 9H. Precisely cut, it provides protection against scratches and breakage.

The set includes installation accessories along with a positioning frame, thanks to which installation is very easy and accessible to literally everyone.

INSTALLATION INSTRUCTIONS:
1) Start installation in the bathroom right after bathing - the water vapor will absorb all the dust from the atmosphere and it will not interfere with your installation.
2) Clean and degrease the surface of the screen thoroughly, then use a dry cloth to polish it to a shine.
3) Place the mounting frame with the glass on the watch screen – the glass will be perfectly centered. Remove the protective film from the top of the glass, then press the glass with your finger in the center of the screen to begin the adhesion process.
4) Remove the mounting frame. Get rid of air bubbles by pressing the whole thing down in a circular motion for a few dozen seconds. Do this so that the adhesive layer bonds to the screen as tightly as possible.

Tech-Protect Glass SPY+ is a premium tempered glass with advanced privacy technology that protects your data from unauthorized access. A special privacy layer limits the visibility of the screen to outsiders looking from the side, so that the content displayed on your phone remains visible only to you. It's the perfect solution to protect the confidentiality of conversations and messages while traveling, working in public places, or everyday use.

The glass provides excellent protection for the display against scratches, bumps and dents thanks to its 9H hardness. It does not affect the touch sensitivity or color saturation, while maintaining the full functionality of the phone. The high-quality oleophobic coating minimizes the amount of fingerprints left behind, and the milled 2.5D edges ensure a smooth touch and comfort of use. The incredible smoothness of the surface has a positive effect on the comfort of everyday work with the phone.

The easy installation procedure makes the installation affordable for any user, even those who are inexperienced in putting on lenses. Perfect clarity preserves the original image display quality.

* Remember to remove and re-add fingerprints after installing the glass, if any.
** Due to the variety of milling of the edges of the displays, after the installation of any glass, a delicate air halo "may" form around the screen. This condition results from the very milling of the screen in a given piece.

Tech-Protect Glass SPY+ is a premium tempered glass with advanced privacy technology that protects your data from unauthorized access. A special privacy layer limits the visibility of the screen to outsiders looking from the side, so that the content displayed on your phone remains visible only to you. It's the perfect solution to protect the confidentiality of conversations and messages while traveling, working in public places, or everyday use.

The glass provides excellent protection for the display against scratches, bumps and dents thanks to its 9H hardness. It does not affect the touch sensitivity or color saturation, while maintaining the full functionality of the phone. The high-quality oleophobic coating minimizes the amount of fingerprints left behind, and the milled 2.5D edges ensure a smooth touch and comfort of use. The incredible smoothness of the surface has a positive effect on the comfort of everyday work with the phone.

The easy installation procedure makes the installation affordable for any user, even those who are inexperienced in putting on lenses. Perfect clarity preserves the original image display quality.

* Remember to remove and re-add fingerprints after installing the glass, if any.
** Due to the variety of milling of the edges of the displays, after the installation of any glass, a delicate air halo "may" form around the screen. This condition results from the very milling of the screen in a given piece.

Tech-Protect Glass Fit+ is a tempered glass that combines protection with aesthetics. Precisely milled edges and minimal thickness make the glass almost disappear on the screen, while maintaining full touch sensitivity.

The 9H hardness on a ten-point scale means that the glass can withstand contact with keys, coins and other sharp objects that you carry in your pocket every day. The thickness of only 0.3 mm practically does not change the profile of the smartphone and does not affect the responsiveness of the screen. The hardened material dissipates the force of the impact, protecting the display from cracks during falls.

The oleophobic coating minimizes the accumulation of fingerprints and makes it easier to keep the glass clean. Crystal clarity preserves natural colors and sharpness of the image. The glass design ensures compatibility with most available cases.

Tech-Protect Glass Fit+ tempered glass is a high-quality protective accessory made of lightweight and precisely milled glass with a thickness of only 0.3mm.

The perfectly matched design fully preserves the sensitivity of the touchscreen. The manufacturer rates its hardness level at 9H on a ten-point scale, which translates into exceptional scratch resistance during everyday use.

The glass is characterized by crystal clarity, thanks to which it retains the natural colors and sharpness of the display. An additional advantage is a special oleophobic coating, which effectively minimizes the accumulation of fingerprints and other impurities on the surface of the glass, thus making it easier to keep it clean.

* The glass is compatible with most cases available on the market.
** Due to the variety of milling of the edges of the displays, a slight halo of air may form around the screen after the film/protective glass is installed on the screen! This is a natural situation and depends on the milling of the screen in a given piece.

INSTALLATION INSTRUCTIONS:
1) Start installation in the bathroom right after bathing - the water vapor will absorb all the dust from the atmosphere and it will not interfere with your installation.
2) Clean and degrease the surface of the screen thoroughly, then use a dry cloth to polish it to a shine.
3) Install the coating as evenly as you can - you can position it with two sheets, gluing them to the side of the device.
4) Get rid of air bubbles by pressing the whole thing down in a circular motion for a few dozen seconds. Do this so that the adhesive layer bonds to the screen as tightly as possible.

Tech-Protect Glass Fit+ tempered glass is a high-quality protective accessory made of lightweight and precisely milled glass with a thickness of only 0.3mm.

The perfectly matched design fully preserves the sensitivity of the touchscreen. The manufacturer rates its hardness level at 9H on a ten-point scale, which translates into exceptional scratch resistance during everyday use.

The glass is characterized by crystal clarity, thanks to which it retains the natural colors and sharpness of the display. An additional advantage is a special oleophobic coating, which effectively minimizes the accumulation of fingerprints and other impurities on the surface of the glass, thus making it easier to keep it clean.

* The glass is compatible with most cases available on the market.
** Due to the variety of milling of the edges of the displays, a slight halo of air may form around the screen after the film/protective glass is installed on the screen! This is a natural situation and depends on the milling of the screen in a given piece.

INSTALLATION INSTRUCTIONS:
1) Start installation in the bathroom right after bathing - the water vapor will absorb all the dust from the atmosphere and it will not interfere with your installation.
2) Clean and degrease the surface of the screen thoroughly, then use a dry cloth to polish it to a shine.
3) Install the coating as evenly as you can - you can position it with two sheets, gluing them to the side of the device.
4) Get rid of air bubbles by pressing the whole thing down in a circular motion for a few dozen seconds. Do this so that the adhesive layer bonds to the screen as tightly as possible.

Tech-Protect Glass Flex+ is a revolutionary hybrid glass that provides maximum screen protection without compromise. The ultra-thin design with a thickness of only 0.28 mm makes it virtually invisible and at the same time extremely durable. With a ceramic coating with a hardness of 7H, it effectively protects against scratches and pressure, maintaining perfect clarity and full sensitivity to touch. The biggest advantage? It doesn't crack or crumble like traditional tempered glass!

Tech-Protect Glass Flex+ is the perfect solution for those who value complete safety without compromise.

INSTALLATION INSTRUCTION:
1. The installation of this glass model is different from traditional tempered glass glued to a thin adhesive layer. Due to the thicker layer of glue, the process is a bit more demanding and requires precision.
2. Clean the watch screen thoroughly. Use a damp cloth to remove any dirt and fingerprints. Then wipe the screen with a dry, soft cloth to completely remove moisture. Finally, use dust stickers to get rid of dust and dust particles.
3. Carefully remove the protective film from the adhesive layer. Precisely align the glass with the screen and gently place it.
4. If any of the edges do not adhere properly, it is likely that the glass has been glued unevenly. In this case, they should be peeled off and re-glued until the desired effect is achieved.
5. Remove air bubbles by gently pressing the glass from the center to the edges. Use your finger or a soft cloth to do this, pushing the air out.
6. Due to the specificity of glass production (polishing, milling), the fitting may require several minutes of work. After proper installation, the final result is aesthetic and durable.

Tech-Protect Bundle 10-Pack Tempered Glass is a comprehensive set of high-quality screen protectors, designed for users who want maximum protection and reliability on a daily basis. Each glass in the set is made of durable, tempered material with a hardness of 9H, thanks to which it effectively protects the screen of the device from scratches, bumps and damage resulting from intensive use.

The ultra-thin design provides full clarity and does not affect touch sensitivity, guaranteeing a smooth, natural smartphone experience. With a precise cutout and a perfect fit, the glass adheres perfectly to the screen, while the oleophobic coating minimizes fingerprints and smudges.

A set of 10 pieces is an economical and convenient solution for both people who have several devices and for those who want to have spare protection always at hand. It is also a great proposition for services and sellers of GSM accessories.

* Due to the various milling of the edges of the displays, after installing the film/protective glass on the screen, a slight air halo may form around the screen! This is a natural situation and depends on the milling of the screen in a given piece.

INSTALLATION INSTRUCTIONS:
1) Start installation in the bathroom right after bathing - the water vapor will absorb all the dust from the atmosphere and it will not interfere with your installation.
2) Clean and degrease the surface of the screen thoroughly, then use a dry cloth to polish it to a shine.
3) Install the coating as evenly as you can - you can position it with two sheets, gluing them to the side of the device.
4) Get rid of air bubbles by pressing the whole thing down in a circular motion for a few dozen seconds. Do this so that the adhesive layer bonds to the screen as tightly as possible.

Tech-Protect Glass Fit+ is a tempered glass that combines protection with aesthetics. Precisely milled edges and minimal thickness make the glass almost disappear on the screen, while maintaining full touch sensitivity.

The 9H hardness on a ten-point scale means that the glass can withstand contact with keys, coins and other sharp objects that you carry in your pocket every day. The thickness of only 0.3 mm practically does not change the profile of the smartphone and does not affect the responsiveness of the screen. The hardened material dissipates the force of the impact, protecting the display from cracks during falls.

The oleophobic coating minimizes the accumulation of fingerprints and makes it easier to keep the glass clean. Crystal clarity preserves natural colors and sharpness of the image. The glass design ensures compatibility with most available cases.

Slim and light case with built-in glass designed to fit perfectly on your Apple Watch.
Defense360 from Tech-Protect is a stylish way to fully protect your Watch.

The integrated tempered glass does not affect the touch sensitivity or the quality of the displayed image.
During installation, degrease the screen surfaces with an alcohol-based liquid.

Tech-Protect Glass Flex+ is a revolutionary hybrid glass that provides maximum screen protection without compromise. The ultra-thin design with a thickness of only 0.28 mm makes it virtually invisible and at the same time extremely durable. With a ceramic coating with a hardness of 7H, it effectively protects against scratches and pressure, maintaining perfect clarity and full sensitivity to touch. The biggest advantage? It doesn't crack or crumble like traditional tempered glass!

Tech-Protect Glass Flex+ is the perfect solution for those who value complete safety without compromise.

INSTALLATION INSTRUCTION:
1. The installation of this glass model is different from traditional tempered glass glued to a thin adhesive layer. Due to the thicker layer of glue, the process is a bit more demanding and requires precision.
2. Clean the watch screen thoroughly. Use a damp cloth to remove any dirt and fingerprints. Then wipe the screen with a dry, soft cloth to completely remove moisture. Finally, use dust stickers to get rid of dust and dust particles.
3. Carefully remove the protective film from the adhesive layer. Precisely align the glass with the screen and gently place it.
4. If any of the edges do not adhere properly, it is likely that the glass has been glued unevenly. In this case, they should be peeled off and re-glued until the desired effect is achieved.
5. Remove air bubbles by gently pressing the glass from the center to the edges. Use your finger or a soft cloth to do this, pushing the air out.
6. Due to the specificity of glass production (polishing, milling), the fitting may require several minutes of work. After proper installation, the final result is aesthetic and durable.

The Tech-Protect Quick Set Spy+ 2-Pack Privacy Glass is an innovative solution for maximum privacy protection during use. A special filtering technology ensures that the screen content is visible only to the user looking directly at the display, while those watching from the side see only the black screen.

The glass combines two key functions - privacy protection and full protection of the display against scratches, cracks and impacts. Made of tempered glass with a highest hardness of 9H, it provides excellent image quality without affecting the responsiveness of the touch screen.

The kit includes two protective lenses and a special installation frame that guarantees perfect positioning and application of the glass without air bubbles. This comprehensive installation system eliminates the common problems associated with tempered glass application, ensuring a professional result the first time.

Ideal for people working with sensitive data, traveling by public transport or simply valuing their privacy in public places.

* Due to the variety of milling of the edges of the displays, a slight halo of air may form around the screen after the film/protective glass is installed on the screen. This is a natural situation and depends on the screen itself.

INSTALLATION INSTRUCTIONS:
1) Start installation in the bathroom right after bathing - the water vapor will absorb all the dust from the atmosphere and it will not interfere with your installation.
2) Clean and degrease the surface of the screen thoroughly, then use a dry cloth to polish it to a shine.
3) Install the shell as evenly as you can - you can position it with the help of the positioning frame from the kit.
4) Get rid of air bubbles by pressing the whole thing down in a circular motion for a few dozen seconds. Do this so that the adhesive layer bonds to the screen as tightly as possible.

Tech-Protect Bundle 10-Pack Tempered Glass is a comprehensive set of high-quality screen protectors, designed for users who want maximum protection and reliability on a daily basis. Each glass in the set is made of durable, tempered material with a hardness of 9H, thanks to which it effectively protects the screen of the device from scratches, bumps and damage resulting from intensive use.

The ultra-thin design provides full clarity and does not affect touch sensitivity, guaranteeing a smooth, natural smartphone experience. With a precise cutout and a perfect fit, the glass adheres perfectly to the screen, while the oleophobic coating minimizes fingerprints and smudges.

A set of 10 pieces is an economical and convenient solution for both people who have several devices and for those who want to have spare protection always at hand. It is also a great proposition for services and sellers of GSM accessories.

* Due to the various milling of the edges of the displays, after installing the film/protective glass on the screen, a slight air halo may form around the screen! This is a natural situation and depends on the milling of the screen in a given piece.

INSTALLATION INSTRUCTIONS:
1) Start installation in the bathroom right after bathing - the water vapor will absorb all the dust from the atmosphere and it will not interfere with your installation.
2) Clean and degrease the surface of the screen thoroughly, then use a dry cloth to polish it to a shine.
3) Install the coating as evenly as you can - you can position it with two sheets, gluing them to the side of the device.
4) Get rid of air bubbles by pressing the whole thing down in a circular motion for a few dozen seconds. Do this so that the adhesive layer bonds to the screen as tightly as possible.

Tech-Protect Glass Flex+ is a revolutionary hybrid glass that provides maximum screen protection without compromise. The ultra-thin design with a thickness of only 0.28 mm makes it virtually invisible and at the same time extremely durable. With a ceramic coating with a hardness of 7H, it effectively protects against scratches and pressure, maintaining perfect clarity and full sensitivity to touch. The biggest advantage? It doesn't crack or crumble like traditional tempered glass!

Tech-Protect Glass Flex+ is the perfect solution for those who value complete safety without compromise.

INSTALLATION INSTRUCTION:
1. The installation of this glass model is different from traditional tempered glass glued to a thin adhesive layer. Due to the thicker layer of glue, the process is a bit more demanding and requires precision.
2. Clean the watch screen thoroughly. Use a damp cloth to remove any dirt and fingerprints. Then wipe the screen with a dry, soft cloth to completely remove moisture. Finally, use dust stickers to get rid of dust and dust particles.
3. Carefully remove the protective film from the adhesive layer. Precisely align the glass with the screen and gently place it.
4. If any of the edges do not adhere properly, it is likely that the glass has been glued unevenly. In this case, they should be peeled off and re-glued until the desired effect is achieved.
5. Remove air bubbles by gently pressing the glass from the center to the edges. Use your finger or a soft cloth to do this, pushing the air out.
6. Due to the specificity of glass production (polishing, milling), the fitting may require several minutes of work. After proper installation, the final result is aesthetic and durable.

Tech-Protect Glass Flex+ is a revolutionary hybrid glass that provides maximum screen protection without compromise. The ultra-thin design with a thickness of only 0.28 mm makes it virtually invisible and at the same time extremely durable. With a ceramic coating with a hardness of 7H, it effectively protects against scratches and pressure, maintaining perfect clarity and full sensitivity to touch. The biggest advantage? It doesn't crack or crumble like traditional tempered glass!

Tech-Protect Glass Flex+ is the perfect solution for those who value complete safety without compromise.

INSTALLATION INSTRUCTION:
1. The installation of this glass model is different from traditional tempered glass glued to a thin adhesive layer. Due to the thicker layer of glue, the process is a bit more demanding and requires precision.
2. Clean the watch screen thoroughly. Use a damp cloth to remove any dirt and fingerprints. Then wipe the screen with a dry, soft cloth to completely remove moisture. Finally, use dust stickers to get rid of dust and dust particles.
3. Carefully remove the protective film from the adhesive layer. Precisely align the glass with the screen and gently place it.
4. If any of the edges do not adhere properly, it is likely that the glass has been glued unevenly. In this case, they should be peeled off and re-glued until the desired effect is achieved.
5. Remove air bubbles by gently pressing the glass from the center to the edges. Use your finger or a soft cloth to do this, pushing the air out.
6. Due to the specificity of glass production (polishing, milling), the fitting may require several minutes of work. After proper installation, the final result is aesthetic and durable.

Tech-Protect Glass Flex+ is a revolutionary hybrid glass that provides maximum screen protection without compromise. The ultra-thin design with a thickness of only 0.28 mm makes it virtually invisible and at the same time extremely durable. With a ceramic coating with a hardness of 7H, it effectively protects against scratches and pressure, maintaining perfect clarity and full sensitivity to touch. The biggest advantage? It doesn't crack or crumble like traditional tempered glass!

Tech-Protect Glass Flex+ is the perfect solution for those who value complete safety without compromise.

INSTALLATION INSTRUCTION:
1. The installation of this glass model is different from traditional tempered glass glued to a thin adhesive layer. Due to the thicker layer of glue, the process is a bit more demanding and requires precision.
2. Clean the watch screen thoroughly. Use a damp cloth to remove any dirt and fingerprints. Then wipe the screen with a dry, soft cloth to completely remove moisture. Finally, use dust stickers to get rid of dust and dust particles.
3. Carefully remove the protective film from the adhesive layer. Precisely align the glass with the screen and gently place it.
4. If any of the edges do not adhere properly, it is likely that the glass has been glued unevenly. In this case, they should be peeled off and re-glued until the desired effect is achieved.
5. Remove air bubbles by gently pressing the glass from the center to the edges. Use your finger or a soft cloth to do this, pushing the air out.
6. Due to the specificity of glass production (polishing, milling), the fitting may require several minutes of work. After proper installation, the final result is aesthetic and durable.

The Tech-Protect Bundle 10-Pack is a comprehensive set of high-quality tempered glass, designed for users who want maximum protection and reliability on a daily basis. Each glass in the set is made of durable, tempered material with a hardness of 9H, thanks to which it effectively protects the screen of the device from scratches, bumps and damage resulting from intensive use.

The ultra-thin design provides full clarity and does not affect touch sensitivity, guaranteeing a smooth, natural smartphone experience. Precise cutout and perfect fit make the glass adhere perfectly to the screen, while the advanced oleophobic coating minimizes fingerprints and smudges, keeping the screen clean for a long time.

A set of 10 pieces is an economical and convenient solution for both people who have several devices and for those who want to have spare protection always at hand. It is also a great proposition for services and sellers of GSM accessories, providing an excellent value for money.

* Due to the variety of milling of the edges of the displays, after the installation of protective glass on the screen, a slight halo of air may form around the screen. This is a natural situation and depends on the milling of the screen in a given piece.

Tech-Protect Glass Fit+ tempered glass is a high-quality protective accessory made of lightweight and precisely milled glass with a thickness of only 0.3mm.

The perfectly matched design fully preserves the sensitivity of the touchscreen. The manufacturer rates its hardness level at 9H on a ten-point scale, which translates into exceptional scratch resistance during everyday use.

The glass is characterized by crystal clarity, thanks to which it retains the natural colors and sharpness of the display. An additional advantage is a special oleophobic coating, which effectively minimizes the accumulation of fingerprints and other impurities on the surface of the glass, thus making it easier to keep it clean.

* Due to the various milling of the edges of the displays, after installing the film/protective glass on the screen, a slight air halo may be created around the screen! This is a natural situation and depends on the milling of the screen in a given piece.

INSTALLATION INSTRUCTIONS:
1) Start installation in the bathroom right after bathing - the water vapor will absorb all the dust from the atmosphere and it will not interfere with your installation.
2) Clean and degrease the surface of the screen thoroughly, then use a dry cloth to polish it to a shine.
3) Install the coating as evenly as you can - you can position it with two sheets, gluing them to the side of the device.
4) Get rid of air bubbles by pressing the whole thing down in a circular motion for a few dozen seconds. Do this so that the adhesive layer bonds to the screen as tightly as possible.