Unidrain

Horizontale P-sifon unidrain met Ø75 afvoer.

Houten vloer Unidrain roestvrij staal 1810 alle AR.

Complete square drain set. Package includes ClassicLine Column grating and frame 10×10 cm, steel drain unit, water trap, outlet unit Ø 75 mm horizontal with side inlets, 3 x adapters (2 pcs. for 40 mm pipes and 1 pc. for 32 mm pipe). The height of the unit can be adjusted +/- 10 mm and rotated 360° in the outlet unit. Truncate the ClassicLine frame to tile level. Minimum tile layer 4 mm. Cleaning cloth included.

Can be freely positioned against the back wall, independent of any side walls.

The drain unit has one wall flange.

Unidrain o-ring for water trap.

Afvoerfitting Unidrain 1001 900 mm.

Available in 8, 10 and 12 mm heights (depending on the thickness of the floor tile). The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame. The frame is non-optional and has two functions: To support the grating and give a perfectly flush finish with the tiled floor.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Complete square drain set. Package includes HighLine Custom base 10×10 cm, steel drain unit, flow guide, water trap, outlet unit Ø 110 mm horizontal with side inlets, 3 x adapters (2 pcs. for 40 mm pipes and 1 pc. for 32 mm pipe). The height of the unit can be adjusted +/- 10 mm and rotated 360° in the outlet unit. Special adhesive is included to glue your own tile to the custom base. Hook and cleaning cloth included.

Complete square drain set. Package includes ClassicLine Column grating and frame 15×15 cm, steel drain unit, flow guide, water trap, outlet unit Ø 75 mm horizontal with side inlets, 3 x adapters (2 pcs. for 40 mm pipes and 1 pc. for 32 mm pipe). The height of the unit can be adjusted +/- 10 mm and rotated 360° in the outlet unit. Truncate the ClassicLine frame to tile level. Minimum tile layer 8 mm. Cleaning cloth included.

Paneel Unidrain Highline CUSTOM 1000

18200040 Waterafvoerlijn 50 mm sluitingshoogte

Geurbarrière, lijn voor 1311.0032, 1311.0050, 1312.0050, 1312.0075 en 1417.0050

Zeepplank Unidrain hoekkolom.

The set consists of a panel, rail, heightener set and screws. The set must be assembled before installation.

Includes 2 x hooks to be used for lifting the panel.

The panel solution is placed directly inside the drain unit.

The rail is specially designed to provide a snug fit. Installed with HighLine frame.

The heightener set to adjust the panel is included, so that the panel can be matched to the frame height.

NB: PVD-treated surface.

Unidrain Highline CUSTOM 900 paneel

For Shower cubicles with three fixed walls.

The drain unit has three wall flanges.

Self-cleaning trap with a capacity of 0.4-0.6 l/s depending on the outlet unit it is installed in. Meets the requirements for capacity and self-cleaning according to EN1253 (the pan-European standard for floor drains) and is VA approved. Suitable for most outlet units, including older models. Can replace water trap 1820.0010 and 1820.0040, if they are installed at the top of the drain unit. A hook to lift the water trap up from the outlet unit and a packet of silicone lubricant are included

Meets capacity and self-cleaning requirements according to EN 1253 (the pan-European standard for floor drains) and is VA-approved.

The water trap can be removed from the outlet unit and then dismantled for cleaning.

Bin bags for Reframe pedal bin. 10 rolls of 25 bin bags. Black plastic (PEHD). 2 pcs. specially designed tape for easy fitting of the bag are included. Volume 4 l.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

For shower cubicles without fixed walls.

The drain unit has four floor flanges.

Including four heght-adjustable feet (40-190 mm).

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Doucherek Unidrain Reframe is een hoekplank van geborsteld roestvrij staal voor de douchenis met flexibele montage, afvoergroeven en een antisliprand.

Ontworpen voor kleinere badkamers waar de ruimte efficiënt moet worden benut, biedt deze hoekplank praktische opbergruimte met een lichte, zwevende uitstraling.

• Hoekmontage voor de douchenis
• Gemaakt van roestvrij staal AISI 304
• Groeven helpen water van het oppervlak weg te leiden
• Antisliprand helpt producten stabiel te staan wanneer ze nat zijn
• Kan worden aangepast aan hoeken die niet precies 90° zijn

Als onderdeel van de Reframe-serie combineert het doordacht design met dagelijkse badkamerfunctionaliteit.

Unidrain afvoereenheid Ø50 mm incl. waterslot

With side drain on the left.

Can be freely positioned against the back wall, independent of any side walls. Only for use with ClassicLine.