Boren en bits - pagina 65

Polishing fleece, voor roestvrij staal, non-ferrometaal, steel sheets, verf op hout, 115 mm, rond, korrel: very fine, 115 mm

Gatenzaag, 73 mm

Bit holder, pozidriv, PZ2

DeWALT DT70531T-QZ schroevendraaierbit

Boorstift, voor beton, metselwerk, versterkt beton, 14 mm, SDS-max, lengte: 540 mm

Bahco 3833-35-C gatenzaag

Boorstift, voor beton, metselwerk, versterkt beton, 18 mm, SDS-max, lengte: 540 mm

Boorstift, hamerboor, 8 mm, SDS-plus, lengte: 115 mm, voor Makita SDS-Plus; XGT HR008GM202

Schroefbitset, 12 stuks, torx, phillips, pozidriv, zeskant, lengte: 25 mm

Gatenzaag, 68 mm

Boorstift, voor beton, plastic, staal, zachthout, soft tile, multimaterial, 5 mm, cilindrisch, lengte: 85 mm

Gatenzaag, voor bakstenen, spaanplaat, zachthout, plastic verstevigd met glasvezel, soft tile, 19 mm

Boorstift, voor beton, plastic, staal, zachthout, soft tile, multimaterial, 10 stuks, 5 mm, cilindrisch, lengte: 85 mm

Boorstift, voor beton, plastic, staal, zachthout, soft tile, multimaterial, 5.5 mm, cilindrisch, lengte: 85 mm

Beitel, voor beton, bakstenen, plat, 10 stuks, SDS-max, lengte: 400 mm, breedte: 25 mm

Boor, spiraalboor, 8 mm, cilindrisch, lengte: 400 mm

Bosch Bit extra-hard

Makita D-40163 boor

Boorstift, voor metaal, 2.5 mm, lengte: 57 mm

For drilling into concrete, masonry, natural and artificial stone, brick, etc. Rotary/percussion masonry carbide tip drill bit

Rapid RP150 Multi Zwart, Blauw

The HSS cobalt spiral drill provides long-lasting performance when drilling in stainless steel. The extended lifespan is due to a 5% cobalt alloy content and fully ground HSS (high-speed steel), which provides outstanding surface quality, wear resistance, and heat protection. Equipped with two cutting edges and two flutes, chips are removed quickly, so the hammer drill lasts even longer. This hammer drill can be used for alloyed and unalloyed steel, stainless steel, cast iron, cast steel, acid- and heat-resistant steel. The HSS spiral drill made of steel is manufactured according to DIN 338. The drilling head is of type N (notch angle) with a 135-degree point angle and a diameter tolerance of h8. Active cutting and perfect centering without displacement are achieved thanks to the two-part tip. This drilling head can be used for alloyed and unalloyed steel, stainless steel, cast iron, cast steel as well as acid- and heat-resistant steels. It has a cylindrical shaft system (the shaft has the same diameter as the drilling head) intended for use in boring stands or screwdrivers.
Package with one piece.

Boor, spiraalboor, 5 mm, cilindrisch, lengte: 86 mm

Boorstiftset, voor hout, spaanplaat, zachthout, spaanplaat, 3 stuks, 25 mm, 20 mm, 22 mm, lengte: 152 mm

Boorstift, voor beton, plastic, staal, zachthout, soft tile, 14 mm, cilindrisch, lengte: 200 mm